Optimization and Performance of Combination Flocculating System in Polymer Flooding

doi:10.3969/j.issn.1006-396X.2017.01.005

›› 2017, Vol. 30 ›› Issue (1): 23-26.DOI: 10.3969/j.issn.1006-396X.2017.01.005

Previous Articles Next Articles

Optimization and Performance of Combination Flocculating System in Polymer Flooding

Received:2016-09-20 Revised:2016-12-10 Published:2017-02-24 Online:2017-02-28

聚合物驱油中复配絮凝剂体系的优选及性能研究

李航^1,2,陈波^1,2

1.长江大学非常规油气湖北省协同创新中心,湖北武汉430100;2.长江大学地球科学学院,湖北武汉430100

通讯作者: 陈波(1967-),男,博士,教授,博士生导师,从事非常规油气资源评价方面研究;E-mail:chpo@yantzeu.edu.cn。
作者简介:李航(1992-),女,硕士研究生,从事非常规油气研究;E-mail:564439669@qq.com。
基金资助:
国家“973”计划项目(2011CB403000)。

Abstract

Abstract:

Aiming at the property of oil-bearing sewage after polymer flooding in LH oilfield, on the basis of the microscopic of suspended matter in oil-bearing sewage, flask experiment was used to evaluate the sewage processing effect of several organic and inorganic flocculation agent used in domestic oilfield. Three kinds of flocculating agent were elected and mixed with VB-1, and the oil removal rate and removal of turbidity were studied. The flocculation effect of different concentration of flocculating agent VB-1 in the mixture was researched and the flocculation effect of different experiment temperature was also investigated. The results showed that the best combination flocculating system was 150 mg/L VB-1+3 000 mg/L JDF. The oil removal rate and removal of turbidity were 95.78% and 88.54% under the condition of 40 ℃. The higher the temperature, the better the flocculation effect of the combination flocculating system. The optimized combination flocculating system FPTY has strong application feasibility in the processing of oil-bearing sewage after polymer flooding in LH oilfield.

Key words: Polymer flooding, Oil-bearing sewage, Flocculating agent, Oil removal rate, Removal of turbidity

摘要： 针对聚合物驱油田采出污水处理难度大,处理成本高的特点,以LH 油田聚合物区块采出污水为研究对象,在对含油采出污水中悬浮物微观形貌分析的基础上,利用烧瓶实验评价了国内油田常用的几种有机和无机絮凝剂的除油率和去浊率,优选出了3种适应性较好的絮凝剂,并与实验室自制的絮凝剂VB-1复配使用,研究了不同絮凝剂VB-1加量下复配体系的除油率和去浊率,并探究了温度对复配体系絮凝效果的影响规律。结果表明,优选出的最优的絮凝剂复配体系FPTY为:150mg/LVB1+3000mg/LJDF。温度为40℃条件时,优选出的絮凝剂复配体系FPTY的除油率和去浊率分别为95.78%和88.54%,且复配絮凝体系FPTY 的絮凝效果与温度成正比。优选出的复配絮凝剂体系FPTY在LH 油田聚合物区块的含油采出水的处理中具有很好的适应性。

关键词: 聚合物驱, 含油污水, 絮凝剂, 除油率, 去浊率

LiHang,ChenBo. Optimization and Performance of Combination Flocculating System in Polymer Flooding[J]. , 2017, 30(1): 23-26.

李航,陈波. 聚合物驱油中复配絮凝剂体系的优选及性能研究[J]. 石油化工高等学校学报, 2017, 30(1): 23-26.

[1]	Yuanyuan He, Huiying Zhong, Songlin Guo, Tingbao Yang. Influencing Factors of Microscopic Oil Displacement Efficiency by Polymer Flooding in Class II Reservoirs [J]. Journal of Petrochemical Universities, 2023, 36(2): 34-41.
[2]	Pengfei Luan, Xiangguo Lu, Weijia Cao, Kaiqi Zheng. Study on the Relationship between Polymer Transport Capacity and Oil Displacement Effect [J]. Journal of Petrochemical Universities, 2022, 35(4): 66-74.
[3]	Li Liu, Yingxue Ma, Ruibo Cao, Shixin Zhou, Zhihao Li. Optimization of Injection Parameters of Adaptive Flooding System after Polymer Flooding [J]. Journal of Petrochemical Universities, 2021, 34(5): 56-61.
[4]	Guochao Liu. Study on Distribution and Plugging Method of Dominant Seepage Channels after Polymer Flooding [J]. Journal of Petrochemical Universities, 2021, 34(4): 46-52.
[5]	Yang Wenwu. Research of Well Pattern Adjustment by Streamline Variation on Main Productive Layers in Post⁃Polymer Flooding Block B [J]. Journal of Petrochemical Universities, 2021, 34(2): 54-59.
[6]	Liu Fan, Zhou Wensheng, Xie Xiaoqing. Experimental Study on Residual Oil of Polymer Flooding Composite Well Network Adjustment [J]. Journal of Petrochemical Universities, 2020, 33(4): 28-33.
[7]	Fu Hongtao, Sun Liyan, Guo Chunping, Jin Yanxin, He Chen. Study on Polymer Flooding of the Upward Series in Second⁃Class Oil Layers in High Water⁃Bearing Sandstone Reservoir [J]. Journal of Petrochemical Universities, 2020, 33(4): 38-42.
[8]	Cao Guangsheng, Sui Yu, Du Mingyu, Sang Congyu, Liu Yijia, Li Shining. Study on Flow Characteristics of Polymer Flooding in Reservoir B of Lamadian Oilfield [J]. Journal of Petrochemical Universities, 2020, 33(3): 31-36.
[9]	Li Bo. Optimization of Salt⁃Resistant Polymer Slugsand and Analysis of the Effect in Test Zone [J]. Journal of Petrochemical Universities, 2020, 33(3): 37-42.
[10]	Wang Minghao. Optimization of Polymer Injection Slug in N Development Area Wang Minghao [J]. Journal of Petrochemical Universities, 2019, 32(6): 44-51.
[11]	Wei Zhijie. A New Efficient Simulation Method for Polymer Flooding Based on Brine Model [J]. Journal of Petrochemical Universities, 2018, 31(03): 44-49.
[12]	Wu Zhibin. Study and Application of Water & Polymer Simultaneous Stratified Injection Process in Single Well [J]. Journal of Petrochemical Universities, 2018, 31(03): 95-100.
[13]	Li Xinyang, Wei Lixin, Zhang Wei. Thermal Cleaning to Remove Sediment of Oil Gathering  Pipeline between Wellhead and Metering Room [J]. Journal of Petrochemical Universities, 2017, 30(4): 85-89.
[14]	Zhang Wenlong, Sun Liyan, Qi Meng, Ye Yuchen. Laboratory Experiment on Inaccessible Pore Volume of Polymer Flooding [J]. Journal of Petrochemical Universities, 2016, 29(4): 35-37.
[15]	Pi Yanfu， Gong Ya. The Variation Laws of Seepage of Hydrophobic Associating Polymer Flooding after Polymer Flooding in Onshore Oilfields [J]. Journal of Petrochemical Universities, 2016, 29(4): 66-71.

Optimization and Performance of Combination Flocculating System in Polymer Flooding

聚合物驱油中复配絮凝剂体系的优选及性能研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics