Strength Analysis of Milling Head of DividedMilling Machine for Pipe Cutting

Journal of Liaoning Petrochemical University ›› 2013, Vol. 33 ›› Issue (1): 74-77.

Previous Articles Next Articles

Strength Analysis of Milling Head of DividedMilling Machine for Pipe Cutting

WU Ming¹， DENG Zilong²， GE Hanlin²， XU Long²

1.College of Petroleum Engineering，Liaoning Shihua University, Fushun Liaoning 113001, China； 2.School of Mechanical Engineering, Liaoning Shihua University, Fushun Liaoning 113001, China

Received:2012-09-27 Published:2013-03-25 Online:2017-07-14

管道切割对开式钻铣机钻铣头强度分析

吴明¹,邓子龙²,葛汉林²,许龙²

1.辽宁石油化工大学石油天然气工程学院,辽宁抚顺113001;2.辽宁石油化工大学机械工程学院,辽宁抚顺113001

作者简介:吴明(1961飊),男,辽宁铁岭市,教授,硕士

Abstract

Abstract: Milling head is the important actuator of divided milling machine. The strength value of milling machine has big affection in reliability when it working. Thus, the static and modal analysis used finite element software ANSYS has important meanings. The geometric model of milling head was builded by 3D software Pro/E and tested the interference of the model. The finite element was constructed through the connector of Pro/E and ANSYS and made modal and static analysis through ANSYS. The results of dynamic simulation show that there is no interference produced. The results of modal analysis show that there is no resonance phenomenon produced. At the same time, the results of static analysis show that the stiffness and strength is satisfied. Theoretically, the results of software provide references for the structure and optimizing design of the machine.

Key words: Pipe , Divided , Milling machine , Milling head , Strength analysis

摘要： 钻铣头是管道切割对开式钻铣机的重要执行元件,其强度的大小对钻铣机工作的可靠性有着非常大
影响,应用有限元软件ANSYS对其进行静态和模态分析有着重要的意义。通过三维软件Pro/E建立钻铣头的几何
模型,并进行运动仿真检验其是否产生干涉,利用Pro/E软件和ANSYS软件的接口将几何模型导入ANSYS软件
中,运用ANSYS软件建立有限元模型进行钻铣头的静态和模态分析。运动仿真结果表明模型未产生干涉,有限元
模态分析结果表明无共振现象产生,有限元静态分析结果表明刚度和强度满足要求,应用三维软件和有限元软件从
理论上为设计的合理性提供了依据,也为优化设计提供了参考。

关键词: 管道 , 对开式 , 钻铣机 , 钻铣头 , 强度分析

WU Ming，DENG Zilong，GE Hanlin，XU Long. Strength Analysis of Milling Head of DividedMilling Machine for Pipe Cutting[J]. Journal of Liaoning Petrochemical University, 2013, 33(1): 74-77.

吴明,邓子龙,葛汉林,许龙. 管道切割对开式钻铣机钻铣头强度分析[J]. 辽宁石油化工大学学报, 2013, 33(1): 74-77.

[1]	Longsheng CHENG, Decai YOU, Dan WANG, Fei XIE. Risk Evaluation Study of Zhoushan Section of Xin'ao LNG Export Submarine Pipeline Based on Kent Method [J]. Journal of Liaoning Petrochemical University, 2025, 45(3): 48-56.
[2]	Yeqiang JIANG, Guiyang MA, Xiangchun JIANG, Zhuo LIANG, Lufei YU. Numerical Simulation Study on Leakage and Diffusion of Hydrogen⁃Doped Natural Gas Pipelines in the Comprehensive Pipe Gallery [J]. Journal of Liaoning Petrochemical University, 2025, 45(1): 59-64.
[3]	Mengna XU, Ruixin BAO, Yingrui SUN, Xiangguang SUN, Yuanzhong QIN. Development of Pipeline Leakage Monitoring Simulation System Based on Virtual Instrument Technology [J]. Journal of Liaoning Petrochemical University, 2025, 45(1): 74-81.
[4]	He ZHANG, Ying GUO, Xianming LANG, Hao GENG, Yan WANG, Fuyin ZHENG. Study on Weak Magnetic Internal Detection Characteristics of Micro⁃Cracks in Long⁃Haul Oil and Gas Pipelines [J]. Journal of Liaoning Petrochemical University, 2025, 45(1): 82-89.
[5]	Lidan FENG, Chuang WANG, Jun QI, Yuanbo SHI. Research on Pipeline Defect Detection Technology Based on Improved YOLOv7 [J]. Journal of Liaoning Petrochemical University, 2024, 44(4): 82-90.
[6]	Wenting YE, Jiangjiang ZHANG, Peiyang XU, Jiaxu MIAO, Mingzhang ZHUANG, Limin HE, Yuling LÜ, Donghai YANG. Study on Low-Temperature Gathering and Transportation Characteristics of High-Water-Cut Crude Oil in Different Pipeline [J]. Journal of Liaoning Petrochemical University, 2024, 44(3): 37-44.
[7]	Linlin LIU, Lijian YANG, Songwei GAO. Energy Change of Pipeline Signal Spatial Propagation Detected by Magnetic Tomography Method [J]. Journal of Liaoning Petrochemical University, 2024, 44(2): 71-76.
[8]	Xingtong Wang, Cheng Feng, Shengyi Wu, Dingqi Xu, Weiqiang Wang, Shengnan Du. Experimental Study of Severe Slugging in Downward Riser [J]. Journal of Liaoning Petrochemical University, 2023, 43(4): 78-83.
[9]	Fuqiang Zhang, Kun Wang, Lijuan Gao, Duoqi Wang, Qiyu Huang. Effect of Interface Characteristics of FRP Pipe Wall/Crude Oil on Low⁃Temperature Transportation of High Water⁃Cut Crude Oil [J]. Journal of Liaoning Petrochemical University, 2023, 43(2): 42-46.
[10]	Biao Gao, Ruotong Zhao, Chuting Kuai, Mengyu Hu, Guofu Wang. Numerical Simulation of Leak Diffusion and Failure Consequences of High⁃Pressure Hydrogen⁃Doped Natural Gas Pipelines [J]. Journal of Liaoning Petrochemical University, 2023, 43(2): 60-66.
[11]	Zhengxing Hu, Ruixin Bao, Xiaodan Bian, Qiqiang Peng, Yu Guo. Research on Modeling Method and Mechanical Influence Parameters of Depressed Pipeline [J]. Journal of Liaoning Petrochemical University, 2023, 43(2): 72-77.
[12]	Yuanjie Liu, Qiang Liu. A Pipe Layout Sequence Optimization Method Based on Disassembly Complexity [J]. Journal of Liaoning Petrochemical University, 2023, 43(2): 86-91.
[13]	Junchi Li, Fei Xie. Study of Stress Corrosion Cracking Behavior of X70 Pipeline Steel in CO₂ Enhanced Mining Environment [J]. Journal of Liaoning Petrochemical University, 2023, 43(1): 38-42.
[14]	Weiming Wang, Wenna Li. Improved Genetic Algorithm to Optimize Differences Control of Heater Bypass [J]. Journal of Liaoning Petrochemical University, 2023, 43(1): 73-79.
[15]	Zhiwei Zhao, Wenquan Jiang, Junfeng Guo, Yanhai An, Zhi Li, Yao Zhang. Crack Failure Analysis of Torch Burner Pipeline in Petrochemical [J]. Journal of Liaoning Petrochemical University, 2022, 42(5): 80-83.

Strength Analysis of Milling Head of DividedMilling Machine for Pipe Cutting

管道切割对开式钻铣机钻铣头强度分析

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics