辽宁石油化工大学学报

辽宁石油化工大学学报 ›› 2006, Vol. 26 ›› Issue (1): 5-7.

• 石油化工 • 上一篇    下一篇

BF3 催化C8 ~ C13混合烯烃的聚合工艺

丁洪生1 , 权成光2 , 张志峰2   

  1. 1 .辽宁石油化工大学, 辽宁抚顺113001 ;
    2 .中国石油抚顺石油化工公司石化一厂, 辽宁抚顺113003
  • 收稿日期:2005-09-15 出版日期:2006-01-25 发布日期:2006-01-25
  • 作者简介:丁洪生(1963 -), 男, 辽宁凌源市, 副教授, 硕士。
  • 基金资助:
    中国石油资助项目(04B50205)

Polymerization Process of C8 ~ C13 Alpha -Olefins Catalyzed by Boron Trifluoride

  1. 1 .Liaoning University of Petroleum & Chemical Technology , Fushun Liaoning 113001 , P .R .China ;
    2 .No .1 Plant of Fushun Company of PetroChina Company Limited , Fushun Liaoning 113003, P .R .China
  • Received:2005-09-15 Published:2006-01-25 Online:2006-01-25

摘要:         聚α-烯烃合成油(PAO)是重要的合成润滑油之一。使用三氟化硼作催化剂对α-烯烃(C8 ~ C13)的聚合进行了研究。考察了温度、压力、反应时间、引发剂、引发剂的质量分数等工艺条件对聚α-烯烃合成油产率的影响。确定了合成聚α-烯烃合成油的最佳工艺条件是温度为30 ℃, 压力为0 .4 M Pa , 反应时间为4 h , 引发剂为正丁醇, 引发剂的质量分数为0.1 %。在最佳工艺条件下, 用10 L 反应釜进行了放大实验, 研究了聚α-烯烃合成油的
物化性能。结果表明, 产品收率为81.42 %, 100 ℃的粘度为4.87 mm2/s , 40 ℃的粘度为21 .15 mm2/s , 粘度指数为126 , 凝点为-62 ℃。合成油具有粘度低, 凝点低,粘度指数高的优异特点。为进一步工业化开发聚α-烯烃合成油提供了基础数据。

关键词:  α-烯烃,  BF3 催化剂,  聚α-烯烃合成油,  聚合工艺

Abstract:

     Poly -alpha -olefins synthetic lubricant (PAO)is one of the important synthetic lubricant .The polymerization of C8 ~C13 alpha -olefins had been studied with boron trifluoride as catalyst .The effects of various kinds of technological condition , such as temperature, pressure , reaction time , various kinds of promoters and mass fraction of the promoter o n the yield of the poly -alpha -olefins synthetic lubricant w ere studied.The optimum technological conditions of poly -alpha -olefins synthetic lubricant are that the temperature is 30 ℃, the pressure is 0 .4 MPa, the reaction time is 4 hours , the promoter is n -butanol, and the mass fraction of the promoter is 0.1 %.Under the optimum technological conditions, enlarge experiment of poly -alpha -olefins synthetic lubricant was carried out with 10 L reactor .The proper ties of the poly -alpha -olefin synthetic lubricant w ere studied.The yield of the poly -alpha -olefins synthetic lubricant is 81 .42 %.The results show that the viscosity at 100 ℃ is 4 .87 mm2/ s, the viscosity at 40 ℃ is 21 .15 mm2/s , the viscosity index is 126 , the condensation point is -62 ℃.The pro ducts of synthetic lubricant have low viscosity ,low condensation point and high viscosity index .This work provides a fundamental data for studying the poly -alpha -olefins synthetic lubricant in industry .

Key words:  Alpha -olefin,  Boron trifluoride catalyst ,  Poly -alpha -olefins synthetic lubricant ,  Polymerization process

引用本文

丁洪生, 权成光, 张志峰. BF3 催化C8 ~ C13混合烯烃的聚合工艺[J]. 辽宁石油化工大学学报, 2006, 26(1): 5-7.

DING Hong -sheng,QUAN Cheng -guang,et al. Polymerization Process of C8 ~ C13 Alpha -Olefins Catalyzed by Boron Trifluoride[J]. Journal of Liaoning Petrochemical University, 2006, 26(1): 5-7.

使用本文

0
    /   /   推荐

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://journal.lnpu.edu.cn/CN/

               https://journal.lnpu.edu.cn/CN/Y2006/V26/I1/5