Journal of Petrochemical Universities
Annual Contents
Journal of Petrochemical Universities 2007 Vol.20
Please wait a minute...
For Selected: Toggle Thumbnails
Preparation Process of Intermetallic Compound SbSn and Its Desulfurization Performance
G UO Ning,YUN Zhi
Abstract282)      PDF (182KB)(219)      
        The influence of quench speed, twice melting , melting time and adding NaCl on structures and desulfurization performance of intermetallic compound SbSn was studied. The results show that at the condition of 30 V and 400 A, the composition of trigonal system crystal structure increases and its desulfurization performance is also enhanced with the increase of quench speed ;after twice melting , the lustration of melting material is increased , therefore crystalline grain and degree of crystal are decreased and the desulfurization performance becomes worse during rapid cooling . The uniformity of SbSn mate rial is fortified , the desulfurization performance gets better with the increase of melting time. The addition of NaCl could increase the degree of crystal and desulfurization performance during the melting process. Thiophene and ethanethiol were used as model compounds to study the mechanism of desulfurization. The result shows thiophene can be absorbed on the surface of SbSn and the C - S of ethanethiol can be broken in reaction.
2007, 20 (1): 1-4.
Preparation and Catalytic Performance of SO 2 - 4 /ZrO 2 - SiO 2 Solid Superacid
LU Guan - zhong, SU Yong,ZHANG S hun - hai, MAO Do ng - sen
Abstract321)      PDF (177KB)(260)      
        A solid superacid catalyst , SO2 -4 /ZrO2 - SiO2 , was prepared by impregnating the Zr(OH)4 - Si(OH)4 co precipitate with a sulfuric acid solution, then drying and calcinating , in which the Zr(OH)4 - Si(OH)4 coprecipitate was prepared with zirconium oxychloride as zirconia sources, silica solution as silica sources and aqueous ammonia as precipitant , respectively , then drying at 110 ℃. The results from XRD and surface area measurements indicate that the addition of SiO2 strongly changes the structure of SO2 -4 /ZrO2 , hence greatly increases its surface area. The effect of preparation conditions such as concentration of sulfuric acid and calcination temperature on the catalytic performance of SO2 -4 /ZrO2 - SiO2 substituted for sulfuric acid for the esterification of n - butanoic acid with n - butyl alcohol was studied. The results show that the yield of butyricbutyl using the SO2-4 /ZrO 2 - SiO 2 catalyst prepared with the concentration of H2 SO4 by 1. 0mol /L and the calcination temperature of 550℃ is higher than 90 % when the molar ratio of butyl alcohol to butanoic acid is 1. 2 ∶1 and without addition of entrainer , which is superior to the reported results obtained using SO2 -4 /TiO2 - WO3 and TiSiW12 O40 / TiO2 catalysts under comparable experiments.
2007, 20 (1): 5-8.
The QSPR Between Connectivity Index and Its Converse Index and Boiling Point of Aliphatic Unsaturated Hydrocarbon
CHEN Yan
Abstract320)      PDF (197KB)(295)      
        On the basis of adjacency matrix , a novel connectivity indexes of mX D and its converse index mX D′were constructed from an approved new atomic v alence δdi . The correlation coefficients be tween 0 XD , 1 XD , 0 XD′, 1 XD′and boiling points for 80alkenes , 39alkynes and 169 aliphatic unsaturated hydrocarbons were made , which were 0. 999 3 , 0. 999 6, 0. 995 5, respectively and better than those of the famous Kier's index (mXv). The result shows that the new 1 XD with good structure selectivity , property relativity and clear physical meaning is easy to calculate , which provides an effective method to predict the aliphatic boiling points of the aliphatic unsaturated hydrocarbons.
2007, 20 (1): 9-12.
Synthesis of 2 - Methy l - 2 - Hydroxy - 1 - Phenyl - 1 - Pentanone
HU Ying - xi,LIU Xia,GUO Juan
Abstract354)      PDF (204KB)(336)      
    First , 2 - methyl isocaproy l chloride was prepared by 2 - methylvaleric acid and thionyl chloride. Second, 2 - methyl - 1 - pheny l - 1 - pentanone was synthesized with benzene and isocaproy l chloride in the presence of anhydrous aluminum chloride as a catalyst. The n, 2 - methy l - 2 - hydroxy - 1 - pheny l - 1 - pentanone was prepared by chlorination and hydrolysis with 2 - methyl - 1 - pheny l - 1 - pentanone in the presence of NaOH and CCl4 as chlorinating agent and tetrabutyl ammonium bromide as the phase transfer catalyst. The result shows :w hen n(2 - methylvaleric acid)/n(thionyl chloride) is 1. 0 ∶1. 5, dropwise temperture and time of thionyl chloride is 40 ℃ and 1. 5 h respectively , reaction time is 2. 5 h, anhydrous aluminum chloride is 18. 5 g , benzene is 45 mL, dropwise time of isocaproyl chloride is 0. 5 h , the yield of 2 - methy l - 1 - pheny l - 1 -pentanone is 92. 7 %;when n(2 - methy l - 1 - pheny l - 1 - pentanone)/n(CCl4) is 1. 0 ∶1. 8 , tetrabutyl ammonium bromide is 6 g , mass fraction of sodium hydroxide is 20 % and reaction time is 5 h , the yield of 2 - methyl - 2 -hydroxy - 1 - pheny l - 1- pentanone can be up to 91%. The structure of the product was characterized by elemental analysis, IR and MS.
2007, 20 (1): 13-17.
Removal of Nitrogen Compounds From Crude Methylnaphthalene Oil by Extraction With Formic Acid
XIONG Jie - ming,ZHANG Li - ping,GONG Liang - fa
Abstract358)      PDF (178KB)(261)      
    The crude methylna phthalene oil (CM NO) contains some nitrogen impurities, such as quinoline , isoquinoline and indole and soon. The nitrogen compounds can be removed off efficiently from CM NO by extraction with formic acid.Experiment was carried out to investigate the effect of the extraction time , temperature , formic acid concentration , volume ratio of solvent to oil on extraction. The result shows that extraction system reaches equilibrium within 3 min for quinoline , isoquino line and methylquinoline , but needs longer time for indole , the formic acid concentration has little effect on removal of quinoline , isoquinoline and methylquinoline but has strong effect on removal of indole , the higher the formic acid concentration,the higher the indole removal efficiency , the removal efficiency for indole is higher below 40 ℃. The yield for me thylnaphthalene is more than 95%, which presents an effective method for removal of nitrogen compounds from CM NO.
2007, 20 (1): 18-20.
Effect of CaO on Hydrogen Production by Vaporization From Biomass in Supercritical Water
WA NG Jing - chang,YUAN Ta - liang,WANG Kun, LIU Xue - w u, LI Zhi - y i
Abstract487)      PDF (203KB)(214)      
    Experiments for hydro gen production w ere carried out in subcritical and supercritical water in a batch - type reactor biomass set up by our selves. Glucose was used as a model compound, and CaO was used as CO 2 remover in experiments. The effects of temperature , residence time and n (Ca) /n(C) on glucose reactions with and without CaO were examined by comparison and the optimal process for hydrogen production from biomass was also suggested. Under the condition of 480 ~530 ℃, above critical pressure , 2. 5%~ 5. 0 %mass fraction of glucose , 3~ 5 min resident time , n(Ca)/n(C) of 0. 45 ~ 0. 52 , the mass fraction of hydro gen is up to 67. 5 %.
2007, 20 (1): 21-23.
Estimation of the Acute Toxicity of Chloro -Aniline Compound to Photobacterium Phosphoreum by Using Topological Index
YANG Chun -feng,FENG Chang -jun,MU Lai -lo ng
Abstract349)      PDF (190KB)(202)      
        On the basis of the chemical topological theory , Kier's molecular connectivity index (mX vp)and Hall's elect rotopological state index(En)o f 14 chloro -aniline compounds were calculated .The quantitative structure -bioactivity relationship (QSAR) between the acute to xicity of 14 chloro -aniline compounds to photo bacterium phosphoreum and En , mX vp was investigated with multiple regression analysis .By using stepwise regression analysis, the best QS AR model was set up and the correlation coefficient was 0 .979 .By using leave - one - out (LOO) of Jackknifed method , the model shows predictability and robustness , the estimated values are close to experimental datas.
2007, 20 (1): 24-27.
Improvement of Method Determining Mass Concent ration of HPAM by the S tarch - Cadmium Iodide
ZHANG Zho ng - zhi,GAO Yu - ge, LU Xiao - gang,WANG Han,ZHANG Qing - jun
Abstract380)      PDF (192KB)(506)      
         The effect of mass concentration of starch on accuracy of determining partially hydrolyzed poly acry lamide(H PAM) concentration by use of starch - cadmium iodide method was studied. The results show that the Abs not only increases with the increase of H PAM mass concent ration, but also with the increase of straight chain starch mass concentration. A way to improve the solubility of straight chain starch was adopted and the best added quantity of starch was found. The improved process for determining H PAM mass concentration was displayed. In the range from 0 to 25 mg /L of H PAM mass concentration , a standard working curve of H PAM mass concentrationvs. solution absorbency was constructed with R2 is equal to 0. 999 8.
2007, 20 (1): 28-30.
Characteristics and Catalytic Performance of Nanocrys talline and Non - Nanocry stalline ZSM - 5 Zeolites
ZHANG Ling - ling,LI Feng - yan,ZHAO Tian - bo,WANG Yue
Abstract371)      PDF (311KB)(267)      
    The characteristics and catalytic performance of nanocr ystalline and no n - nano crystalline ZSM - 5 Zeolites were studied. The zeolites were characterized by XRD and SEM , the acidity was measured by NH3 - TPD, surface area and pore volume were determined by N2 adsorption. Toluene alkylation and o - xylene isomerization were chosen and the catalytic activity was estimated with impulse minisize reactor - chromatogram device. The results show that to luene alkylation and o - xylene isomerization convertion of nano crystalline ZSM - 5 zeolite are 60. 98 %(450 ℃) and 90. 38 %(500 ℃) respectively , which are higher than that of non - nano crystalline ZSM - 5 zeolite(46. 18% and 75. 59 %), so nano crystalline ZSM - 5 zeolite has better catalytic activity.
2007, 20 (1): 31-34.
Activity of La 1 - xSr xCo 0. 5Mn 0. 5O 3 Perovskite - Type Catalyst for Simultaneous Removal of Diesel Soot Par ticulates and NO x
SUN Zhi - qiang,WANG Hong
Abstract306)      PDF (188KB)(220)      
    A series of complex oxide La 1 - xS r x Co 0. 5Mn 0. 5O 3 perovskite - type catalysts in which La 3+ is partly substituted for S r 2+ were synthesized at low temperature through a combustion process and the catalysts were characterized by XRD, IR and BET. The activity of the catalysts for simultaneous removal of NO x and diesel soot particulates were examined in details using temperature programmed reaction (TPR) technique. The results show that after partial substitution of La 3 + with Sr 2+ the oxygen vacancy concentration increases significantly , B 3 + - B 4 + system is formed and consequently the catalytic activity for simultaneo us removal of NO x and diesel soot particulates is significantly improved. It is found through catalytic property testing that catalytic activity is best when x =0. 4 and the catalyst and the soot is mixtured tightly , temperature of soot combustion is 305 ~ 435 ℃, the conversion rate of NO x can reach to 43. 7%.
2007, 20 (1): 35-38.
 

A Novel Synthetic Method of 4-Chloro-1,2-Bimethyl-Benzene by High Selective Chlorination Reaction

QIAN Jian-hua, ZHANG Qing-chun, LIU Lin, XING Jin-juan, GONG Shu-hua
Abstract142)      PDF (893KB)(0)      
 

The selective chlorination reaction of the aromatic ring among the aromatic compounds is very important in the economy and environmental protection aspects. A novel chlorination reaction system HCl-H2O 2-CH3COOH was applied to react with o-xylene. Compared to the traditional Lewis acid catalysts which comprised sulfur and zeolite catalytic chlorination system, it took on much superiority such as high-selectivity, high-yield, simple operation, savings and environmental protection etc. The reaction conditions were controlled, the molar ratios of hydrogen peroxide, hydrochloric acid to o-xylene were 5.0,4.0 respectively, the reaction was processing under 70 until the feeding was finished and then the reaction was 2 h under 90 . The conversion ratio of the raw material is over 99%, the yield is 96.9% and the selectivity is over 99% under this condition.

2007, 20 (1): 39-41.
 
Synthesis and Catalytic Properties in Cyclohexane Oxidation of Macrocyclic Heterodinuclear Complexes Encapsulated in MCM-41
GAO Li-juan, LI Rui-feng
Abstract286)      PDF (885KB)(250)      
 
Nine macrocyclic d-f heterodinuclear complexes [M1M2L](NO 3)(H 2O)n(M,L stand for metal and ligand) were synthesized. Nine d-f heterodinuclear complexes were immobilized on MCM-41 mesoporous materials to prepare encapsulated catalyst by impregnation. The samples were characterized by using IR and UV-Vis, XRD, ICP-AES and TG/DTA techniques. The results show that the structures of heterodinuclear complexes in MCM-41 are unchanged. The catalytic properties of the prepared catalysts were studied by cyclohexane oxidation. The results show that they have better activity in cyclohexane oxidation; TOF values of these encapsulated catalysts are in the range of 20.4~49.2 h-1; the conversion of cyclohexane is the highest (72.1%) when acetic acid is used as solvent. The influence of time, temperature and the amounts of the oxidant and catalyst on cyclohexane oxidation was also investigated. The best reactive conditions are reaction time of 10~12 h, reaction temperature of 343~393 K, H2O2 amount of 5~15 mL and catalyst content of 0.5~1.0 g respectively.
2007, 20 (1): 42-47.
Adsorptive Desulfurization by Modified Zeolites
XU Lin-gang, LI Yong-hong
Abstract272)      PDF (920KB)(520)      
A series of adsorbents involving modified ZSM-5,Y,MCM-41 molecular sieves were prepared by ion-exchanging method for gasoline desulfurization. The composition and specific surface area of the adsorbents were determined by XRD technique. The effect of adsorption conditions on the desulfurization performance of the adsorbents was studied. The results show that the desulfurization performance varies for different adsorbents, CuY performs the best and the optimum adsorption conditions is ambient temperature , atmospheric pressure and mass ratio of adsorbent to oil ratio of 0.15. By analyzing the varations of the adsorbent CuY through regeneration process, the mechanism of adsorptive desulfurization was investigated.
2007, 20 (1): 48-51.
Suspension Bed Hydrocracking of Atmospheric Residue From Dagang Oil Field
ZHANG Lei,MU Bao-quan, DENG Wen-an, QUE Guo-he
Abstract345)      PDF (849KB)(305)      
 
Suspension bed hydrocracking technology and water soluble catalyst were used for upgrading of atmospheric residue from Dagang oil field. The relations among metal composition of the catalyst, reaction conditions, coke forming and conversion were systematically investigated. After optimization, the yields of AGO and VGO are 21.2% and 47.7% respectively from processing atmospheric residue under the condition of 430 ℃, 1.0 h-1 space velocity, 7 MPa and catalyst addition amount with 300 μg/g in once through operation, toluene insolubles yield level of 1.4%, a total conversion of AR which has a boiling point lower than 524 ℃ can reach above 80%.The constitutes of catalyst and reaction temperature are the main factors which affect the conversion of materials and coke formation, the conversion of materials and coke formation increase with the extend of reaction time, the conversion has little change and the trend of coke formation decreases with the increase of reaction pressure. The recycling can improve the conversion of residue but the degree is too small.
2007, 20 (1): 52-55.
Preparation of Hyperbranched Epoxy Resin and Its Performance
WU Bi-yao, ZHANG Jun-heng, CHEN Yao, YIN Wen -hua
Abstract325)      PDF (947KB)(488)      
 
The AB2 monomer was prepared by trimellitic anhydride (TMA) and ethylene glycol.The syntheses of hyperbranched polymer based upon TMA as a core molecule and AB2 monomer which contains two single carboxylic group and one hydroxy groups were studied. Two types of hyperbranched polyester (G1,G2) with different relative molecular weight were obtained by reaction between TMA and AB2 monomer and reaction between G1 and TMA respectively with different mole ratio. Using phase transfer catalyst between epichlorohydrin and potash salt hyperbranched polymer, hyperbranched epoxy polymer of G1′ and G2′ was synthesized. The structure of products was characterized by using IR, GPC and 1HNMR. The results show that G1 and G2 have narrow relative molecular weight distribution with 1.008 1 and 1.011 0 respectively; the IR shows that the hyperbranched epoxy polymer is formed.
2007, 20 (1): 56-59.
Synthesis of 5-o-Tolyl -2-Pentene With Na/K 2CO 3
YANG Jin-xiang, ZHENG Jia-ming, ZHANG Shui-ying, BAI Yun-fei
Abstract285)      PDF (806KB)(230)      
5-o-tolyl -2-pentene(OTP) was prepared by o-xylene and 1,3-butadiene under sodium as catalyst and potassium carbonate as dispersing agent .The effects of catalyst dosage, mass ratio of dispersing agent to catalyst, reaction temperature, reaction time and molar ratio of o-xylene to 1,3-butadiene were investigated. The best technical parameters were obtained : the molar ratio of o-xylene to 1,3-butadiene is 5∶1, reaction temperature is 175 ℃, reaction time is 2.5 h, mass fraction of catalyst is 0.25%, mass ratio of dispersing agent to catalyst is 16∶1.The yield of OTP is 71.2% under the best technologic conditions. The technology has a series of advantages, for example, the process is simple, the reaction time is short, what's more, it's easy to achieve industrialization open up.
2007, 20 (1): 60-62.
Investigation on Slective Oxidation of CO in Hydrogen-Rich Gas for Nano Au/ZnO/TiO 2 Catalyst
WANG Chao,XU Xin,LUO Guo-hua
Abstract361)      PDF (883KB)(251)      
 
The catalytic activity and selectivity of catalysts prepared by coprecipitation method with different precipitants, calcined temperature and the pretreatment condition with different content of Au and ZnO loading dispersed over nanoparticles TiO 2 for CO oxidation in H 2-rich gas was studied. The simulated material gas was used as reaction gas and the evaluation on catalytic activity of product was made through microreaction- chromatograph instrument. The catalyst was characterized by XRD and BET. The results show that the activity and selectivity of the catalysts are greatly changed with the variation of the ZnO loading, the kind of precipitant, calcination temperature and pretreatment condition; the catalyst Au(2%)/ZnO(2%) /TiO 2 with (NH 2)2CO as the precipitants, calcined at 300 ℃, pretreatment in H 2 and reaction temperature for 30℃ has optimal activity and selectivity.
2007, 20 (1): 63-66.
Optimum Design of Multi-Holes Tube Distributor of Plate Air-Cooled Cooler
WEI Li-wa, SUN Tie
Abstract341)      PDF (993KB)(260)      
 
Since the heat exchanger plates are designed along vertical direction, the uniform level of the inlet medium has vital effect on the whole efficiency of cooling rate. The multi-holes distributor optimum design was discussed.The structure design of multi-holes distributor was put forward and the design method was mathematically described ,then deduced the formula of pressure reduction. Flow pattern in the distributor was simulated by CFX software. The results show that the effect of uniform distribution is good. These have some importance to fundamental thought of distributer optimum design and formular reduction of pressure on the distributor design.
2007, 20 (1): 67-69.
Numerical Simulation of Reactor for Methanol Steam Reforming in Automobile
LI Cong, LI Xing-hu, JIANG Lei, SONG Ling-jun
Abstract335)      PDF (922KB)(675)      
 
In order to investigate the temperature field and the distribution of the volume fraction of mixed gas in methanol reforming reactor, a two-dimensional mathematical model was presented for describing the complex physical and chemical processes in the reformer of methanol-steam. The numeration of the steady field in the reactor was made with software STAR-CD by using TGrid mesh technology and laminar flow model which dispersed the equation by finite volume difference method and solved by using SIMPLE arithmetic. The simulation result can describe the temperature field and the distribution of volume fraction of mixed gas in methanol reforming reactor. The model reliability was verified experimentally on self-designed equipment. The model can predict the temperature and volume fraction of various compositions, because the experiments dates are very close to simulated ones. The effect of the tube diameter on the reactor was investigated by using the model. The result shows that with the increase of diameter, the temperature is increased, but there is nearly no change of compositions volume fraction.
2007, 20 (1): 70-73.
Calculation and Analysis on the Performance of Adjustable Ejector
SHEN Sheng-qiang, ZHANG Kun
Abstract392)      PDF (870KB)(818)      
 
A scheme through measuring crush needle in the nozzle for adjusting the ejector was presented. A mathematical model for the performance of adjustable ejector was established and used to analyze the effect of cross section area variation of the nozzle on the parameters of entrainment ratio, fluid pressures and flow rate and so on. The results indicate that the outlet flow rate can be controlled within a stable extent by adjusting the cross section area of the nozzle, the adjustable nozzle can extend the effective working range of ejectors.
 
2007, 20 (1): 74-76.
Experimental Investigation and Analysis on the Response Velocity of a Swing SMA Spring Actuator
WANG Hong, YAO Xiong-liang
Abstract419)      PDF (947KB)(320)      
According as the electrothermal driving principle of SMA springs, the simulation of SMA spring,s response velocity was made and analyzed, at the same time, an experiment on a SMA spring actuator of biomimetic propel was investigated. The result shows that the response velocity of the actuator is related with the driving current, the cooling speed and the pre-tensile length, the response velocity of SMA actuator is improved by increasing the driving current and the cooling speed, which is in accord with the result of simulation. In addition, the response velocity of the actuator is affected by the pre-tensile length, the response velocity of the actuator is improved by choosing an appropriate pre-tensile length, but the SMA spring will come into being irreversible deformation if the pre-tensile length is too large.
2007, 20 (1): 77-80.
 
The Effect of Soil Resistivity on Cathodic Protection Potential Distribution Outside of Tank Bottom
 
DU Yan-xia, ZHANG Guo-zhong
Abstract241)      PDF (938KB)(380)      
 
A mathematical model was established for the cathodic protection potential distribution outside of tank bottom, in which the inhomogeneity of medium was taken into account. The effect of soil resistivity change along vertical direction on potential distribution was studied through numerical simulation. The simulated results indicate that the non-uniformity is further intensified due to the bitumen sand base; soil resistivity in the position where auxiliary anodes are placed has significant effect on potential distribution; there is a buried depth of anode for optimal potential distribution under different geological conditions.
2007, 20 (1): 81-84.
 
Prediction of Flash Points of Fatty Alcohols Based on Artificial Neural Networks
PAN Yong, JIANG Jun-cheng
Abstract268)      PDF (828KB)(247)      
 
A quantitative structure-property relationship (QSPR) model based on artificial neural networks was established to predict the flash points of fatty alcohols. A set of topological indices was used as molecular structure descriptors to describe the molecular structure characteristics of fatty alcohols. Using the back-propagation artificial neural networks which have the satisfactory nonlinear prediction ability, the correlation between molecular structures and flash points of fatty alcohols was studied with molecular structure descriptors as input parameters and flash point as output one. The results show that the predicted flash points are in good agreement with the experimental data, which are superior to those of conventional group contribution methods. The method proposed can be used to predict not only the quantitative relation between flash points and molecular structures of fatty alcohols but also the flash points of organic compounds for engineering.
2007, 20 (1): 85-89.
Application of Particle Swarm Algorithms to Optimization of Chemical Production Process
CHANG Xiao-ping,QIN Jian-hua, Yigong LOU
Abstract349)      PDF (840KB)(351)      
Basic particle swarm algorithms were intelligentized. Based on the intelligentized algorithms and MATLAB, simulation regarding optimization of benzene-toluene flash vaporization process during process of chemical production was made. The simulation result shows that the amount of benzene in vapor phase product reaches the maximum under the condition of effective adjustment of temperature, pressure and diffluence coefficient and the production process is optimized. It also proves that the intelligentized algorithms are practical in optimization of chemical production process.
2007, 20 (1): 90-93.
Data Mining Techniques for Structure of Single XML Document 
MEI Dong-xia, ZHANG Xiao-ming
Abstract230)      PDF (898KB)(225)      
An algorithm based on structure of XML was proposed. XML was parsed using JAVA DOM in order to get XML document tree. The label of XML was stored as label path. Then, frequent transactions were obtained through mining association rules on label paths. The results show that if only the structure of XML is anomaly, the efficiency will be improved when minimal support is increased.
2007, 20 (1): 94-98.
Ex Site-Bioremediation of Petroleum-Contaminated Soil With Exogenous Microbe
WEI Xiao-fang, ZHANG Zhong-zhi﹡, GUO Shao-hui, JI De-kun, LUO Yi-jing, SU You-ming
Abstract314)      PDF (1035KB)(381)      
Experiment was undertaken for ex site-bioremediation of oil-contaminated soil which comes from Dagang oilfield, whether the exogenous microbes accelerate the rate of the bioremediation or not is studied and the impact factors on the biodegradation of the petroleum-contaminated soil were investigated too. The collected soil were divided into two groups then mixed, and the total petroleum hydrocarbon(TPH) was 8 416, 16 385 mg/kg respectively. The TPH of the soil was monitored during the treatment and the influence factors such as indigenous consortium, bio-stimulating, different exogenous microbe, bulk agent (sawdust), the varied initial TPH of the soil were investigated. The components changes of the bio-treated oil and the untreated oil were analyzed by GC-MS. The experiment was lasted for 300 d. When the water content of the soil is given, the exogenous microorganism can speed up the biodegradation of the petroleum greatly, and the reduction ratio of TPH reached to 79% with the combination of the exogenous microbe and bulk agent. The results of GC-MS show that the alkane can be better metabolized by microorganisms when their molecular weight are less than C 28 and the microbes can biodegradate the polycyclic aromatic hydrocarbon efficiently.
2007, 20 (2): 1-4.
Adsorption of Nickel From Aqueous Solution by Humin
LIU Zhi-rong, ZHOU Li-min, WEI Peng, PETER Warwick, NICK Evans
Abstract346)      PDF (1039KB)(416)      
 
The experiment tested that humin can enrich Ni 2+ by means of liquid scintillation counting. The procedures were effected by pH value, amount of humin and initial aqueous concentration of nickel. There may be exist reversible transitions among humic acid, fulvic acid and humin for variation of ultra-violet of peat or humin into nickel solution. Freundlich equation can describe the adsorption reaction of Ni 2+ onto humin excellently. Nickel-humin -dual-complexation mode play an primary part in the adsorption owing to Freundlich [KG*3]adsorption [KG*3]exponent 0.684 4. Freundlich adsorption exponent (0.638 2,
0.684 4)and common logarithm of adsorption index (1.693 2,1.711 5)for peat and humin are almost equal. They indicate that humin may control the binding ability of Ni 2+ onto peat. The results show that humin can act as a potential material for permeable reactive barrier.
2007, 20 (2): 5-8.
 
The Treatment of Oily Wastewater With a Modified Lignin-Based Oil Removal Flocculant
YANG Lin, LIU Ming-hua*
Abstract368)      PDF (1035KB)(558)      
The modified lignin-based oil removal flocculant containing the dithiocarbamate group, denoted as MLOF, was prepared by chemical modification of alkali lignin, a byproduct from the pulp and paper industry. Then MLOF was adopted to treat the oily wastewater. And the flocculation conditions were optimized. The results show the removal percentages of oil, COD Cr, suspended solid (SS) and colourity of the effluent can reach to 88.2%, 71.5%, 90.5% and 93.7% respectively under such conditions as 6.7 of the effluent pH value and 35 mg/L of the flocculant dosage etc. Moreover, the comparison tests with various flocculants indicated that the amount of MLOF was little when treated oily wastewater and the flocculation performance of the modified lignin-based oil removal flocculant apparently prevailed over such high-molecular flocculants as polyacrylamide (PAM), polyaluminium chloride (PAC) and polyferric sulfate (PFS) etc. 
2007, 20 (2): 9-11.
Separation Process of Oleic Aicd and Linoleic Acid by Solvent Crystallization
CUI Guo-gang, JIA Shao-yi, ZHANG Cheng, WU Song-hai*
Abstract249)      PDF (1034KB)(307)      
The solvent crystallization separation process of oleic acid and linoleic acid was investigated by using methanol solvent. The results show that the crystallization temperature and the proportion solvent have big influence on the solvent crystallization separation process of oleic acid and linoleic acid. Decreasing crystallization temperature decreases the mass fraction of oleic acid in crystal and increases the mass fraction of linoleic acid in filtrate. Decreasing proportion solvent increases the mass fraction of oleic acid and linoleic acid. The magnetic field has influence on the separation process, it is favorable to the solvent crystallization separation process of oleic acid and linoleic acid. The quantitative results show that under the effect of magnetic field the mass fraction of oleic acid in crystal increases by 1.73%~2.48% and the mass fraction of linoleic acid in filtrate increases by 1.68%~3.19%.
2007, 20 (2): 12-14.
Application of GPC-ELSD in the Deterimination of Relative Molecular Weight and Its Distribution of VGO
ZHUANG Li-hong, TIAN Yan-wen, LZhen-bo, ZHANG Da-wei
Abstract375)      PDF (997KB)(525)      
 
A High performance gel permeation chromatography(GPC),evaporative light-scattering detector(ELSD) method were applied to determine the relative molecular weight and its distribution of vacuum gas oil(VGO),adopting linear calibration with kown relative molecular weight calibration standard and complicated mathematics operation. Also the precision of the technique was evaluated and the relative molecular weight between GPC and VPO was compared. The results show that the relative error is less than 1%, comparison with traditional method of VPO the analysical rate is promoted five times, the sample oils less to 1/10. The technique is accurate, fast and high level of automatic operation. 
2007, 20 (2): 15-17.
Preparation and Characterization of W 2N/TiO 2-Al 2O and It's Catalysis for Thiophen HDS
ZHANG Qiang, LI Bao -shan*, SUN Gui -da, ZHOU Zhi-jun
Abstract447)      PDF (1118KB)(271)      
 
The complex supporters with different mass fraction of TiO 2 for preparation W 2N/γ-Al 2O 3-TiO 2 catalyst were made by titanic acid tetra-butyl ester sol-gel method and γ-Al 2O 3 as raw materials. The catalyst precursors, WO 3/TiO 2-Al 2O 3, with different WO 3 content were prepared at 500 ℃ baking for 5 h after loading ammonium paratungstate。The precursors were deoxidized and nitrification in H 2/N 2 (volume ratio of 1∶(4~5) gas-flow of 10 800 h-1 through temperature programmed could get the catalysts. And the catalysts were characterized by means of XRD,BET,XPS and TG/DTA. The influence of mass fraction of TiO 2 on its specific surface, its acid amount and its performance for thiophen HDS was investigated in miniature high pressure device of the fixed bed. The results show that when the mass fraction of TiO 2 is 6% in the catalyst, its acid amount and its specific surface are the largest, they are 0.184 9 mmol/g and 107.2 m 2/g respectively. And the activity of the catalyst for thiophene HDS is the best, at 330 ℃, pressure 3 MPa, weight hour space velocity 6 h-1, hydrogen oil ratio 900∶1, the conversion rate of thiophen is up to 56.4%. 
2007, 20 (2): 18-22.
Iron Removal and Its Effect on Turbidity in the Oil Field Produced Water
LI Fang-wen, WU Jian-feng, XU Xiao-hong, LI Meng, ZHANG Xiao-Yan, CHEN Yi-chun, WANG Yu-tao
Abstract380)      PDF (1051KB)(331)      
Iron removal in the oil field produced water and effect of iron mass concentration in the outlet water on turbidity were explored by addition alkali process. Iron contents were determined by 1,10-phenanthroline spectrophotometry and portable turbidimeter was adopted at the determination of turbidity. Results show that pH of inlet water has significant effects on iron removal, turbidity reduce and anti-corrosion of treatment devices. Iron removal is bad and corrosion of treatment device could not be restrained when pH is below 7, which resulted in negative iron removal rate. Better pH is about 8.3 where iron removal and anti-corrosion of treatment devices are attained. And the quality of outlet water can meet the A1 quality standards of recommended indexes in SY/T5329-94 about the injection water quality for clastic rock oil fields, and its turbidity keep invariablenes at a dwell time of 2.5 h. However, outlet water turidity at 6.6 and 7.3 of pH rose gradually because of Fe(OH) 2 oxidation. Coagulant can promote Fe(OH) 2 settlement and major removal mechanisms of Fe(OH) 2 include settlement, interception based on filtration and adsorption from theoretical analysis. At a low pH, electrochemical corrosion made treatment devices release iron which induces outlet iron contents above inlet iron contents. On the contrary, at a high pH, it is blockaded owing to protective layer formation and cathode reaction suppressed.
2007, 20 (2): 23-25.
 
Corrosion and Simulative System of Hydrogenation Reactor Effluent Air Coolers
REN Xiao-guang, XIE Yun-feng, XUAN Zheng-nan
Abstract451)      PDF (1087KB)(279)      
The corrosion mechanism of system of hydrogenation reactor effluent air collers was approached. By confecting simulation corrosion solution, it was researched the effect of experimental in various conditions on annual corrosion rate by means of the corrosion rate testing equipment of resistance probe and CMB-1510B portable instantaneous corrosion rate meterage. The investigated conditions included concentration of corrosion inhibitor, corrosion factor(Kp), pH value and synergistic effect. Results show that BTA corrosion inhibitor is an excellent inhibitor for system of hydrogenating reactor effluent air coolers, there exists good synergistic effect between (NaPO 3)6 and ZnSO 4 compounds in NH 4Cl solution; at the same time, also indicate that annual corrosion rate rises obviously with the increase of corrosion factor, annual corrosion rate rises obviously with the decrease of it when pH value changes in lower range, effect of high pH value on annual corrosion rate lessens on the whole.
2007, 20 (2): 26-29.
Preparation of Fe and Ni Nanopowders by Arc-Discharge Methods
LIAN Shu, LU Zhong-ren, SHI Gui-mei, LI Ying-min
Abstract292)      PDF (1857KB)(306)      
Fe and Ni nanopowders were prepared in mixture gas of H 2 and Ar by arc discharge method. High-melting-point metals W and Mo were added to the raw material (bulk Fe or Ni). The structure, morphology and sizes of the nanopowders were analyzed using X-ray diffraction, transmission electron microscopy, BET, oxygen-nitrogen analysis and chemical analysis. The results show the oxide layer of Fe and Ni is destroyed and the temperature of melting sphere of Fe and Ni is increased due to adding high melting sphere of W and Mo, the productivity of nanopowders has been improved by 50%. The mass fraction of W and Mo in the as-prepared samples is only about 0.01%, and the purity of nanopowders is almost unchanged. The average sizes of Fe and Ni nanopowders are slightly increased under the same condition including atmosphere and pressure as well as power when high melting point metal is added into raw materials. The productivity of adding W in the raw materials is higher than that of adding Mo.
2007, 20 (2): 30-33.
Flow Simulation of Atmosphere-Vacuum Distillation for Crude Oil
GE Yu-lin, SHEN Sheng-qiang
Abstract342)      PDF (1158KB)(452)      
New flow was need to be rearranged in order to satisfy the requirement of technology due to the reconstruction of atmosphere-vacuum distillation equipment for enlarging working ability in the present condition. Based on the fundamental of distillation, MESH model including equations of mass balance, phase equilibrium, mole fraction summations and heat balance for atmosphere-vacuum distillation column was established. The key parameter such as temperature and pressure of product was obtained through solution of the model on Pro/II platform. The comparison of simulation results with requirement of spot technology was analyzed. Good agreement between the results of simulation and requirement of spot technology approves that the model is valid and the rearrangement of flow satisfies the requirement of technology. The profiles of temperature and rate of vapor and liquid versus tray number reflect the influence of feeds, products, and cooling cycle in the middle of columns on process of distillation very well.
2007, 20 (2): 34-39.
Synthetic Process of Tungoil Modified Phenolic Epoxy Resin and the Performance of Room Temperature Cured
YIN Wen-hua, CHEN Yao, WU Bi-yao*
Abstract418)      PDF (1054KB)(506)      
A tungoil-phenol compound(TAP) and the tungoil modified phenolic epoxy resin(TMP) which were synthesized in the presence of acid catalyst, and the structure of these compounds were characterized by FTIR and GPC. FTIR analysis shows that the reaction between tungoil and phenol undermined the conjugate double bond of tungoil molecules, a new substitute product with phenol was formed. When the substitute product reacted with formaldehyde in the acid conditions and further reacted with epichlorohydrine, a tungoil modified phenolic epoxy resin(TMPE) was synthesized. The GPC analysis shows that resin is a mixture of tungoil modified epoxy resin and phenolic epoxy resin, and the molecular weight of tungoil modified phenolic epoxy resin and phenolic epoxy resin were 3 482 and 619 respectively.Solidification performance for the tungoil modified phenolic epoxy resins and E-44 epoxy resin at room temperature were investigated. The results show that when the mass ratio between tungoil modified phenolic epoxy resin and E-44 epoxy resin is at the range of 0.5 to 2.0, the higher tensile strength can be obtained.
2007, 20 (2): 40-42.
CFD Simulation on Homogeneous or Aggregative Fluidization of FCC Particles
LIU Wen-dong, ZHANG Kai, BI Ji-cheng
Abstract320)      PDF (1771KB)(516)      
Fluid catalytic cracking(FCC) plays an important role in the processes of the heavy oil refining industry. A thoroughly understanding of fluid characteristics in the gas-solid fluidized beds is helpful for designing the FCC units. A new two-fluid model developed by Brandani S and Zhang K is used to numerically investigate the hydrodynamics of FCC particles in the platform of CFX 4.4, a commercial CFD software package. Simulation is carried out in a two-dimensional fluidized bed with 0.25 m in width and 0.70 m in height. The particle with a diameter of 6.4×10- 5m and a density of 1 225 kg/m 3 is employed as solid phase. Two typical kinds of fluid dynamics, i.e., homogeneous fluidization and aggregative fluidization, are obtained under corresponding to superficial gas velocities, which are in good agreement with classical theories as well as experimental dates from the literatures.
2007, 20 (2): 43-46.
 
Performance of Environmental Friendly Phosphorous Flame-Retardant Polyester
WU Quan-cai, JIANG Tao, CHEN Xin
Abstract362)      PDF (974KB)(253)      
Structures of environmental friendly phosphorous flame-retardant polyester were characterized through infrared spectra (IR), the performance of its properties such as intrinsic viscosity, differential scanning calorimeter (DSC), oxygen index (OI) and its spinnability was investigated. The results show that the flexible segments in phosphorous flame-retardant monomer were also introduced into the backbone of the polyester macromolecules, which causes the decrease of the phosphorous flame-retardant polyester glass transition temperature (θ g) and melting transition temperature(θ m). The synthesized phosphorous flame-retardant polyester resins have a very good flame retardantability and spinnability; when the mass fraction of phosphorous flame-retardant monomer was 4.5%, the oxygen index of phosphorous flame-retardant polyester reached to 32.8%. The tensile strength and crystallinity decreased owing to the much more space volume of phosphorous flame-retardant polyester. The results indicate that the properties for phosphorous flame-retardant polyester can satisfy the requirements for the manufacture of polyester fibers.
2007, 20 (2): 47-49.
Identification of Friction Factor on Waxy Oil Pipeline
CAI Jian, LI Xiao-ping, GONG Jing*, SONG Sheng-kui
Abstract378)      PDF (1076KB)(309)      
Based on inverse transient analysis method, the identification calculation was performed by minimizing the inverse least square problem representing the difference between the measured and predicted transient response in the waxy oil pipeline. And Levenberg-Marquardt method was adopted to optimize the friction factors. The hydraulic transient was modeled using MOC. The Jacobian matrix of the friction factor’s sensitivity was obtained by direct differentiation of the method of characteristic equations. By means of an example, the errors between the measured values and the calculated values of the middle point on the waxy oil pipeline were compared. The calculated values were solved by means of average, formular and identification friction factors. The results show that the identification method has good evaluation for the internal state variables. Identification basing on inverse transient method can be used to improve the accuracy of simulation and control with pipelines.
2007, 20 (2): 50-53.
Safety Assessment for Pressure Pipeline System Containing Defects Based on GB/T 19624-2004
WANG Ya-xin, XIE Yu-jun
Abstract424)      PDF (1136KB)(222)      
The probability assessment method for pressure piping system containing defects in petrochemical industrial piping was put forward based on GB/T 19624-2004,considering random factors. Safety assessment program for pressure piping system containing defects was worked out. The program not only can assuredly assess pressure piping system containing defects, but also the failure risk caused by each individual defects is got in pipeline containing defects, thus the failure risk of the whole pipeline system is gained.
2007, 20 (2): 54-57.
Elastic-Plastic Finite Element Analysis of the Internal Pressure Vessels With Large Nozzles
GUI Liang, LI De-xin*, ZHANG Jun
Abstract357)      PDF (2383KB)(279)      
The elastic-plastic finite element analyses of the internal pressure vessels with the different ratios of the diameter of nozzle to the diameter of vessel are carried out to investigate the stress concentration in the nozzle-vessel junction. The results show that the heaviest stress concentration is found at the interval nozzle-vessel junction of the longitudinal symmetry plane, while the stress concentration around the external junction is decrease because of the welded joint. In the process of loading, the stress around the junction linearly increases at first and then the range of the high stress area enlarges. The ratio of the diameter of nozzle to the diameter of vessel has greater effect on the distribution area of high stress in plastic deformation stage. Compared with large opening without nozzles, the stress concentrations around the junction are sharply reduced because of the nozzles.
2007, 20 (2): 58-62.
Gear's Predictor-Corrector Algorithms on Molecular Dynamics Simulation of Nanometer Grinding
ZHAO Heng-hua,CAI Guang-qi
Abstract225)      PDF (1736KB)(292)      
Nanometer grinding is the important methods of achieving the super- precision machining.The extremely thin chips can be produced by nanometer grinding. The experimental showed that the very fine chips can be down to 1 nm. Therefore molecular dynamics computer simulation can be used to analyze the mechanism of nanometer grinding.The subject which deals with the interaction between the grinding grain particles and workpiece particles was studied by the method of Gear’s predictor-corrector algorithms. The equation of motion was built up, and solved by numerical method. Then the speed and displacement of these particles were obtained.
2007, 20 (2): 63-65.
Experiment on Shearing Demulsification of W/O Emulsion
JIANG Xue-mei, DONG Shou-ping, ZHANG Hong-guang
Abstract270)      PDF (1357KB)(263)      
In order to study the feasibility of the shearing demulsification of W/O emulsion, a Couette double-cylinder device was designed to form a lamina flow, and its shear intensity was controlled by the rotate speed of the inner cylinder. The force of single droplet is analyzed according to hydrokinetics, and the affine deformation model is put forward and validated by experiment which basically agreed with Taylor G I and Cox R G theory. The results show that shear is propitious to droplets aggregation. Based on the relation curve of droplets diameter with the revolution of inner cylinder, it was found when the rotation velocity of inner cylinder is 50~150 r/min ( shearing strenghth of 8.67~26.01 Pa), the maximal diameter and average diameter are all larger than that of droplets which are not in shear flow. It was shown that shear can accelerate droplets aggregation only within a valid shear range. Therefore,a proper shear flow can be introduced into the separate device to improve the separate efficiency of W/O emulsion.
2007, 20 (2): 66-68.
 
Two Novel Criteria of Deformation of a Single Droplet:Estimation of the Effect of Shear Flow on Deformation of a Single Drop by the Ratio of Long Radius to Short Radius or Stretching Rate 
ZHANG Hong-guang, DONG Shou-ping, WANG Yan-li, LIU Guo-biao, JIANG Xue-mei
Abstract218)      PDF (1138KB)(266)      
Two new type criteria of deformation of a single droplet were introduced to estimate the effect of shear flow on deformation by the ratio of long radius to short radius or stretching rate, and they were analyzed and compared through the experiments. The experiments show that the ratio of long radius to short radius and stretching rate grow with the increase of shear velocity and the deformation shrinkage coefficient of a single droplet increases at first and then decreases. Compared with to the theoretical results it deviates greater with emulsifier. The shear stress attained by the stretching rate agrees better with the practical value than that by the ratio of long radius to short radius.
2007, 20 (2): 69-72.
Stress Corrosion Crack Initiation Analysis of Multilayered Urea Reactors
SONG Ming-da, WANG Wei-qiang, CHEN Lu-bin, XU Shu-gen
Abstract352)      PDF (3472KB)(289)      
Analysis of samples taken from the cracking area of the multilayered urea reactors verified the existence of stress corrosion cracking (SCC) cracks. The influence factors of SCC in multilayered urea reactors were investigated. The results show that the leak detection steam may condense in the interlayer clearances, which would cause alkaline medium concentration at the heavy weld. It was the initiation and propagation of micro-cracks under alkaline environment and local high stress concentrations that lead to the SCC of heavy girth weld urea of the multilayered reactors. The results can give beneficial directions to avoid SCC of layers and catastrophic ruptures of multilayered urea reactors.
2007, 20 (2): 73-76.
 
The Failure Probability Analysis of Ethylene Cracking Furnace Tube Based on Risk
WANG Wen-he, SHEN Shi-ming
Abstract234)      PDF (1047KB)(197)      
The ethylene cracking furnace tube is the key component of the cracking furnace; its failure will bring serious consequences such as the fire explosion etc. According to methods of Monte Carlo and risk analysis theory of API581 of American petroleum institute, it was provides qualitative and quantitatively analysis failure probability of the ethylene cracking furnace tubes for a petrochemical corporation, and obtains the failure probability of this furnace tube. Some results can be seen by the two methods, the failure probability calculated by Monte Carlo method increased with the increase of the runtime of furnace tube under creep and carburization; while the failure probability calculated by API581 only considering creep is lower than that computed by Monte Carlo method.
2007, 20 (2): 77-79.
Scenery Simulation Based on the Iteration Function System and the Free Surface Modeling
HAN Yun-ping, ZHANG Yan*, GUO Lai-de
Abstract270)      PDF (2117KB)(249)      
 The fractal theory is adapted to resolve the simulation of irregular-shaped objects, however, the modeling technology is adapted to the modeling of regular-shaped objects. It can simulate the nature scenery to the life by combining the iteration function system(IFS)of fractal theory with the free surface modeling technology. With the application of iteration function system and the free surface modeling technology to computer aided design (CAD) environment and used the interface modeling Object ARX of CAD and Visual C++ to study the simulative algorithm of natural scenery. With the use of iteration function system to simulate the algorithms of 3D fractal plants. It applied the free surface (B-spline surface) to simulate a hillside. The practical application of a hillside and plants with fruit was given, it indicated that the simulative effect was natural and living.
2007, 20 (2): 80-83.
 
Global Stability in a n-Species System With Time Delay
LI Shi-tao, LI Dong-mei
Abstract290)      PDF (1065KB)(194)      
 One of the most interesting topics in ecology systems is the stability of species. It is a n-species (one-prey, the others-predator) ratio-dependent predator-prey system with time delay and functional response at the seme time and was studied. By differential inequality constructing suitable Lyapunov functional, a sufficient condition was obtained for the global stability of the positive equilibrium of the system. Finally, the numerical simulation result of population model was given.
2007, 20 (2): 84-87.
The Euler Number Study of Image and Its Application
LIN Xiao-zhu, JI Jun-wei, GU Ying-ying
Abstract198)      PDF (1098KB)(418)      
Euler number of image is one of the most important characteristics in digital topology. The connectivity of the binary image was deeply researched in order to understand the essence of Euler number. The relationship between Euler number and the neighbor number of foreground run was proposed as a formula based on the two basic concepts of Euler number and neighbor number. It is a new idea to part computed Euler number of two dimesion image. It has been applied to count the number of objects with irregular shape.
2007, 20 (2): 88-91.
Hilbert-Huang Transform of Pressure Fluctuation Signal in SCISR
ZHANG Jian-wei, XUAN Shu-peng
Abstract323)      PDF (3768KB)(340)      
The Hilbert-Huang transform(HHT)was applied to analyze the pressure fluctuation signal in submerged circulative impinging stream reactor. The intrinsic mode function(IMF) was extracted from the pressure fluctuation in submerged circulative impinging stream reactor(SCISR). The non-linear and non-stationary characteristics of the pressure fluctuation signals were demonstrated. Analyzing the energy distribution of high, middle,low frequency segment and its transfer within different IMF, the relationship between the flow regimes identification in SCISR and the energy distribution of the different frequency segment IMF were founded. The results show that the rotate speed gradually rose, the impinging course of particles would caused the vortex with different scales and energy distribution of IMF would caused diversification. Hilbert-Huang transform method exposes internality rule between flow pattern and energy distributing of IMF component that is obtained by decomposing pressure fluctuation signal of SCISR using EMD. At the same time, quantificational proof can be provided.
2007, 20 (2): 92-96.